145€ with Coupon for TOOLTOP ET829 OSC + DMM + Waveform Generator 3 – BANGGOOD

General characteristics

Display resolution

320 (horizontal) * 240 (vertical) pixels

Display size

2.8inch TFT color screen diagonally

Display backlight time

adjustable

Display backlight brightness

adjustable

Power supply

AC 100V〜240V、50Hz〜60Hz;DC 15W fast charge

Power consumption of the whole machine

Oscilloscope range≤400mA, multimeter range≤200mA

Battery

18650 lithium battery 2000mAh x 2

Battery level indicator

Yes

Auto sleep

the time can be adjusted or turned off, and there will be a sound or display prompt before sleep.

Sound prompt

On/off optional; there are many kinds of voice prompts, such as button sound, high pressure or over-range alarm sound during measurement, and some AI voices that may be added, etc.

To turn off the sound, you can choose to turn off the sound of the whole machine, or just turn off a selected prompt sound.

Use time

about 10 hours for oscilloscope range, about 20 hours for multimeter range

Operating environment

0℃〜40℃, <75%RH

Storage conditions

-10℃~60℃, <90%RH

Dimensions

100mm X 210mm X 40mm (L × W × H)

Weight

480g

Number of channels

 Channel CH1, Channel CH2

Analog bandwidth

80MHz (single channel), 50MHz (dual channel)

Maximum real-time sampling rate

250MSa/s (single channel)）,125MSa/s (dual channel)

Waveform interpolation

(Sin x) /x

Record length

When single channel, the maximum is 6K; when dual channel, the maximum is 3K

Horizontal scale range

5nS/div〜50S/div, 1 > 2、5steps

AD converter

8-bit resolution, simultaneous sampling of each channel

Vertical scale range

1 X: 10mV/div-10V/div; 10X: 100mV/div-100V/div

Vertical measurement range

±4 grid

Optional analog bandwidth limit

20MHz

Low Frequency Response (-3db)

≤10Hz at BNC

Vertical Gain Accuracy

±3% in “Normal” or “Average” acquisition mode

Input resistance

1MΩ/15

Input Coupling

DC,  AC,  GND

Probe attenuation

1X,   10X

Support probe attenuation factor

1X,  10X,  100X

Input protection voltage

300Vpp

Trigger Type

Edge Trigger

Trigger Mode

Auto, Single, Normal

Trigger level

±4div

Edge-triggered slope

Rising edge, falling edge, rising edge or falling edge

Voltage parameter measurement

peak-to-peak, RMS, average, peak, maximum, minimum

Time parameter measurement

frequency, period, duty cycle, positive pulse width, negative pulse width

Cursors

Voltage difference between cursors, time difference between cursors

Smart cursor 1 group, the capture point keeps tracking the current waveform when the cursor moves, and the current cursor position information, voltage difference and time difference are displayed below.

Spectral Analysis FFT

Yes

Storage capacity

2000 groups of DMM data, 200 groups of waveform records, with storage file manager

Filtering

high pass, low pass

Math operation

FFT

Afterglow option

Yes (afterglow effect is required to make Lissajous graphics)

Afterglow selection is divided into multi-level optional.

Computer real-time communication

USB communication

Waveform zoom

Yes

AI waveform preview

a small window is added above the main interface to display the thumbnail of the waveform for preview, and with an indicator to indicate that the current main interface waveform is at a certain position in the entire collected waveform.

Waveform frequency

Sine wave: 1Hz～5MHz

Square waves: 1Hz～500KHz

Triangular wave: 1Hz～500KHz

Amplitude

Fixed-point output, maximum 5Vpp (50Ω)——0Vpp, 0.1Vpp, 0.2Vpp, 0.5Vpp, 1Vpp, 2Vpp, 3Vpp, 5Vpp

Frequency Resolution

0.2Hz

Number of channels

1

Vertical resolution

8 bit

Output Impedance

 50Ω

Square waves pulse width accuracy

±20nS