RadioMaster R168 2.4GHz 16CH Over 1KM PWM SBUS S.port Nano Receiver Compatible FrSky D16 Support Telemetry RSSI VBAT for RC Drone
ONLY €17,04 for RadioMaster R168 2.4GHz 16CH Over 1KM PWM SBUS S.port Nano Receiver Compatible FrSky D16 Support Telemetry RSSI VBAT for RC Drone
*PLEASE NOTE that to avoid customs duties, select Banggood Express or EU Priority Line
For more RadioMaster offers – HERE
For Banggood Coupons see – HERE
RadioMaster R168 2.4GHz 16CH Over 1KM PWM SBUS S.port Nano Receiver Compatible FrSky D16 Support Telemetry RSSI VBAT for RC Drone
Description:
Brand Name: RadioMaster
Item Name: R168 Nano Receiver
Model: R168
Weight: 10g
Size: 40*26*16 mm
Number of channels: 16 channels
Frequency range: 2400-2483.5Mhz
Power supply range: 4.5-6V
Protocol: Frsky D16 Compatible V1
Output format: PWM, SBUS, S.Port
Telemetry: S.port, RSSI output, VBAT (up to 18V voltage detection)
Control distance: more than 1km
Failsafe protection: CUSTOM (customized for all channels), HOLD (failsafe hold), NO PULSES (no pulse)
Antenna length: Approximately 15 cm
Features:
PWM, SBUS and S.Port Output
Battery voltage telemetry built in (Reads main flight battery voltage up to 18v)
Bind Method:
1. On the receiver, presses and hold the bind button and power on the receiver at the same time. The receiver LED red and green lights will be on at the same time, the receiver is now ready to bind.
2. The multi-protocol RF of the remote control select the D16 protocol, presses the [BIND] option, the red light of the receiver will flash indicating successful bind.
3. Exit [BIND] mode on your radio then power off and power on again the receiver. At this time, the green light of the receiver is always on, this indicates the bind process was a success.
The remote control opens the mode menu when binding. This receiver has no PWM output, so choosing 1-8 or 9-16 will have no effect. SBUS always outputs channels 1-16.
Ch1-8 Telem ON: The receivers PWM interface outputs 1-8 channel signals, and telemetry is turned on
Ch1-8 Telem OFF: The receiver,’s PWM interface outputs signals from channels 1-8, and telemetry is turned off
Ch9-16 Telem ON: Receiver PWM interface outputs 9-16 channel signals, and telemetry is on
Ch1-16 Telem OFF: The receiver PWm interface outputs 9-16 channel signals, and telemetry turned off
Setting Fail-safe:
The receiver supports a variety of fail-safe protection methods, you can select the corresponding settings in the remote-control. Failsafe mode to customize the fail-safe protection
Failsafe mode Failsafe setting option description:
1. Not set: If the runaway protection is not set, the remote control will pops up a corresponding prompt to remind you to set the runaway protection
2. Hold: Failsafe hold, keep the channel output at the last moment before losing signal
3. No pulses: no pulse, when the receiver is out signal range, the output signal of all channels will be shut down
4. Receiver: On the receiver short press the blND button for less than 1 second, the receiver LEd green light flashes twice, this will save the current channel values and stick positions of the remote control as the receiver failsafe values
5. Custom: Select [Set] to enter the following interface, you can define each channel value in this interface, select the lowest
Channels=>Failsafe option, you can send the current settings to the receiver as the receivers failsafe values
Package Included:
1 x R168 Nano Receiver
ID:1757299 – SKUF40562
